I have had Hughesnet HN9000 service in Long Barn, CA (95335) since 2011. This is a vacation home/rental and consequently it is not easy to schedule service, or be there to push buttons to diagnose things. (I do receive e-mails from our automation, so I know when things are working). Recently, the received signal strength (as reported by the HN9000's status info) has been below the normal 170-175 value, and has been variable. Last weekend when we were having frequent stoppages, I noticed it was 90, then would climb to 110, then back to 90. Throughput was stopping intermittently even though station status showed normal. The symptoms seem consistent with a dish that is on the edge of the beam lobe vs. centered on it. The dish was clean and had not been moved or bumped, and I can't see that any vegetation has grown into the view of the satellite. Sometimes pine cones fall in the woods and could have bumped the dish, as could have squirrels, freeze/thaw motion etc. Since the system has not been checked, aimed, or tuned for 5 1/2 years, I would really like to get someone to come out and re-aim it. I have the $7/mo. basic service / warranty plan. Hughesnet customer support has been very difficult to deal with - i.e. I got all the way through system checks and to the rep agreeing to send someone out, but they couldn't schedule because of a computer problem. Someone was supposed to call me back to schedule. That was a week ago. I started over with them today and we were back to trying to run diagnostics, which this time turned up no issue, since the problem is intermittent. Then they quoted a $125 fee to open a service call, "plus parts and labor" ($125 even with the warranty plan ? why do I have it ?). I have tried e-mail support, but there seems to be no consistency between communications (they don't read the referenced case numbers I provided). I don't think this is a DIY project, as I know aiming is very sensitive. Any ideas how to get help would be appreciated.
Welcome to our community and thank you for your post. I was able to locate your account and run diagnostics, which came back great. Your signal strength currently is 15 points above the average for your area. It is totally normal for signal strength to fluctuate, especially when weather and outdoor conditions are changing.
With that said, it does not mean your system is without issue and we could be looking at hardware failure, especially considering it's age. Do you notice if the signal drops during the morning, day or night or in specific weather conditions like foggy or high humidity?
Good Morning Amanda - the last time I had problems, the weather was cloudy and rainy one day, and crystal clear the next day. Similar issues both days. The clear day had higher signal strength (130) but was still below what I historically had observed. The behavior is that connectivity would suddenly stop (i.e. just browsing Amazon), then maybe 10 minutes later would start again, work for a few minutes then completely stop again. I rebooted everything, made sure no one was doing anything data intensive etc. So, started to check the signal strength .... Thanks for checking.
Hi Amanda, I haven't noticed anything like unusual with respect to the LEDs, but haven't made it a point to look. The normal pattern is to see a couple of blue lights blinking. I did check the HN9000 status via its web interface and nothing was showing "red".
Can you give it a test tonight and tell me if you notice any of the things I mentioned happening? Can you try rebooting your router first and testing out the internet before rebooting the modem? Also you said scheduling is hard.. would it be difficult for us to arrange a tech to come to the location and replace anything? Someone over 18 would need to be there.
Hi Amanda - I am not physically at the site now, and it is a 3+ hour drive away. Our co-owners will be there next week - Thursday afternoon and Friday 12/29 & 30 and I can coordinate asking them to observe the LEDs when they experience connectivity problems, "button pushing", and feedback. I was hoping to try to coordinate a tech visit, if that's the next step, when they are present. Is there a way for you to monitor performance during their visit ? Is there any way to see system logs/status from Dec 9-11 ?
I am able to see incoming security camera images ~180kb e-mailed to me 6-10x per day (so I can tell if the Hughesnet link is "up").
WiFi Router attached to the modem is a Linksys E2000.
BTW, I did receive a Voicemail from tech support with an 888-301 number for callback, and a PIN. I haven't called back yet.
I agree gokartergo24 - I suspect it is a wet feedhorn or just old everything.
guppypond - Don't worry about calling back. I will set up a free visit from the technician to come out and replace most of that equipment. It seems that the windows for troubleshooting as well as the difficulty of walking people who may not be familiar with the equipment.
I can probably accommodate either of those days but will need to talk to our field operations office to make it happen. Any specific times of the day that are best to have the technician go out?
Thank you Amanda! Best times are Thursday (12/29) afternoon (12-4pm), Friday (12/30) morning. They will also be at the property Saturday, Sunday and leaving sometime Monday morning. You should have the land-line phone number at the service location in the account. I can give you the cell number for the people who will be there (iMessage only, out of cell range) and my cell number via direct message.