Forum Discussion
Create a Hidden Network
I want to make our home network 'hidden' so it does not broadcast its existence. How? Customer support says: "Our records indicate that our networks have to be visible for out customers to access the...
The person you spoke to has no idea what they're talking about because it wasn't on their script.
Here's how you do it:
1. Important: I would find a laptop that you can wire in with a lan cable in case things go bad.
2. Go to http://192.168.42.1 on the laptop and log into the wifi settings (unless that IP's changed on your setup).
3. Make sure you jot down your wifi info for DHCP, particulalrly:
a. The wifi net name (whatever you have it set at - each band 2.4, 5, 2.4Guest, 5Guest will have different net names)b. The subnet mask (usually 255.255.255.0)
c. Router IP: (usually 192.168.42.1 if the same as in #2)
4. In the Wifi Settings box:
a. click on 2.4GHz, then uncheck SSID Broadcast.
b. Repeat for the 2.4GHz Guest
c. Repeat for the 5GHz
d. Repeat for the 5GHz Guest
5. Double check everything on the 2.4/5GHz w/wo Guest tabs, then click Save Settings.
Voila... no one will be able to see your network on their list.Edit: Oh... make sure you test it before you disconnect your wired laptop.
gaines_wright wrote:Sounds like the modem password has been changed. To get back to the "admin" password press the reset button on the back of the modem for 10 seconds.
NO!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
DO NOT, under any circumstances*, hold the reset button in for any length of time. This could create a situation that would require a tech visit to fix, and which the customer would be responsible for paying.
*ONLY ever perform the above under the explicit instructions of a HughesNet representative.
----------------------------------------------------------------------------------------------------------------------------------------------------------------
The customer reset procedure for the HughesNet HT2000W modem is as follows...
How to reset to factory settings
- On the back of the HT2000W (right under the white label), there is a ‘Reset’ button.
- Use a paper clip (or some small/thin object to insert in the hole)
- Insert the paper clip, press the button one time and release (DO NOT hold the button in)
- Press the WPS button on the front of the HT2000W (may need to press firmly)
- After the lights on the HT2000W are back on, login using the password on the back of the modem. (Refer to the User Guide for appropriate modem lights)
This procedure also resets the WiFi settings GUI password to the factory default (admin).
@GabeU wrote:
gaines_wright wrote:Sounds like the modem password has been changed. To get back to the "admin" password press the reset button on the back of the modem for 10 seconds.
NO!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
DO NOT, under any circumstances*, hold the reset button in for any length of time. This could create a situation that would require a tech visit to fix, and which the customer would be responsible for paying.
Don't remember if I had to reset my ht2000 when I installed it. I'm not going to try it now after reading that! That is, unless I forget the password.
From:
https://www.hughesnetinternet.net/reset-your-hughesnet-modem/
Reset your HughesNet modem literally at the touch of a button. You’ll find the reset button either on the back or at the base of your modem, depending on which model you have. Because the button is extremely small, you might need to use something pointed to hold the button, such as a toothpick or a ballpoint pen.
Hold the button down until all the lights on the modem turn off and then back on. If your modem model does not have a reset button, simply unplug the modem. Plug it back in after at least one minute.
I'll take your word about the danger in doing this. Very poor design IMO, if a customer can "break" the modem by holding in a button too long.
That brings up another question: Can Hughes reset the password remotely?
Very interesting. Hopefully a rep can clarify which method is correct, or if they're both correct. I've just seen, over time, warnings of what can happen if the button is held down for too long, which seems to be reverting it to a state that requires a tech visit so that they can run the setup process again, which apparently includes things that the subscriber can't do themselves, even with instructions. I've seen varying descriptions of what "too long" is, so I don't know the answer.
And I've always meant to ask about that website, as well, as in whether it's an official HughesNet website.
Again, hopefully they'll give a clarification.
