Forum Discussion
No access to router on 192.168.0.1
Still getting up to speed on HughesNet... The HT2000w has all the radios disabled and I'm running through a D-Link 655 with Ubiquiti AP's at this location. I'm trying to get the HN usage meter prog...
It's a complicated scenario...
The HT2000w has three addresses, and your DLink router should have one address on the "LAN" side...HT2000w Modem: 192.168.0.1
HT2000w Router: 192.168.42.1
HT2000w Guest Wifi: 192.168.43.1
When you look at the WebGUI for your DLink router, what address are you using to access it? What page pulls up when you attempt to visit http://192.168.0.1 ?
Can you screenshot and show us the Dlink WAN Configuration page, as well as the LAN Configuration page?
According to page 15 of the manual for your Dlink Router, it uses a default address of 192.168.0.1 in the LAN configuration, which you must change to a subnet that the HT2000w isn't using. So on the LAN Configuration of the DLink Router, set it to 192.168.2.1 with a subnet of 255.255.255.0
I strongly urge against changing any of the LAN settings of your HT2000w, such as the IP address or subnet.
_____________________________________________________________Basically, what is happening is that your computer is asking "Hey, 192.168.0.1, what's up?" and the first device going back down the chain from the computer responds, instead of the device that should be. The chain being HT2000w > Dlink > Computer
THAT, or, your Dlink has some form of a firewall that dislikes routing private address spaces.
Take a look at whatever the IP is that the D-Link is set up as the gateway IP address. Usually it's 192.168.0.1, but it might be something different in your configuration. It's also possible it or the mask (should be 255.255.255.0) was set incorrectly. Either way, that's the IP you want to use in the Usage Meter, as well as the web browser.
The Usage Meter and the configuration pages do not need wifi to operate, but it does need to communicate with the modem at that IP (which in turn needs to communicate with HN).
Worthwhile to note that it does take a few minutes after rebooting the modem for the configuration pages to be active.
THANKS for the reply...
The address on the D-Link is 192.168.1.1
Digging deaper into what apears to be router settings, I'm seeing 192.168.42.1
Can I or SHOULD I change that setting to 192.168.1.1?? and will that get me access to the meter software?
It's a complicated scenario...
The HT2000w has three addresses, and your DLink router should have one address on the "LAN" side...HT2000w Modem: 192.168.0.1
HT2000w Router: 192.168.42.1
HT2000w Guest Wifi: 192.168.43.1
When you look at the WebGUI for your DLink router, what address are you using to access it? What page pulls up when you attempt to visit http://192.168.0.1 ?
Can you screenshot and show us the Dlink WAN Configuration page, as well as the LAN Configuration page?
According to page 15 of the manual for your Dlink Router, it uses a default address of 192.168.0.1 in the LAN configuration, which you must change to a subnet that the HT2000w isn't using. So on the LAN Configuration of the DLink Router, set it to 192.168.2.1 with a subnet of 255.255.255.0
I strongly urge against changing any of the LAN settings of your HT2000w, such as the IP address or subnet.
_____________________________________________________________Basically, what is happening is that your computer is asking "Hey, 192.168.0.1, what's up?" and the first device going back down the chain from the computer responds, instead of the device that should be. The chain being HT2000w > Dlink > Computer
THAT, or, your Dlink has some form of a firewall that dislikes routing private address spaces.Here is some follow up info...a bit confused, I'm not seeing a conflict.
What page pulls up when you attempt to visit http://192.168.0.1 ? Can you screenshot and show us the Dlink WAN Configuration page, as well as the LAN Configuration page?
That's... Odd... Is it accessible if you are directly connected to the HT2000w?
