Forum Discussion
Upload Issue again
GabeU,
Ok, finally got Testmy.net figured out except for one issue, combined testing with max data set.
You see the tabs to the right of 'optional'? Both will set the 'minimum' data size but won't affect the maximum so it still tests anything it wants and of course, if it tests something reasonable the first time and runs quickly it will rerun with more data the next time so it is very important that I remember to click nfw. I'm following your instructions but unless I test upload and download separately I have no control over the maximum data used.
Hughes Level 4 called today (1/11/19) and when she had me run the upload test it was 33Kbps up and 21.3 down. Unplug the modem, bypass the router, long periods of silence and 'still buffering' for 25 minutes until it finally steamed without buffering but I haven't a clue what she did and I got the idea that she had a quota on either words or characters used, kink of like Twitter. I appreciated what ever she did but as she trying to get off the phone I asked if 2215 ms ping rate wasn't a touch long. She said she didn't know, 'bye'. I've never asked any tech about that before so I don't know if only certain techs are familiar with ping rates. I let it go and won't complain unless it becomes a consistant issue. What is your average ping rate? I don't know if testmy.net arbitrarily picks Dallas to ping but that's what this is testing. I understand that a high ping rate will affect the loading of a page which is what I'm running into. Slow to connect, handshake, etc. but once loaded it streams with litte buffering now. She must have done something, 1.5 Mbps up - 25Mbps down. Just so it stays. Thanks for the info.
Oh, you're right, I wasn't able to see that your note about being out of data was addressed to someone else. I've yet to figure out this board.
It may be hard to see if on your device, but my reply, including the question about being out of data, was directed at Lorrihager. She's only posted once so far, so I reverted to the basic, starting questions for her.
Regarding your question about the speed testing, the only way I know how to set up automatic testing for both upload and download is like the following, in which I've used the Gen4 test sizes, with the download being the 15MB size instead of 12MB due to the aforementioned resizing problem.
For download and upload testing, it should be set up like this...
Note that "Combined" is selected, and that the download size is 15MB and upload size is 3MB, and that the "nfw" box is checked. The "nfw" stands for "no forwarding", which means the test won't upsize to something larger if it doesn't last long enough. Even with that checked I'd still use the 15MB size for the download, as that size doesn't upsize on its own, so it should be doubly sure not to do so. And I chose every 5 minutes for 5 times due to that being the most commonly requested testing protocol, with this being run a few times a day, for a total of 15 test of each for the day. To start the testsing, you would click "Start Automatic Test", then leave that browser page open. You can continue to use the net on other open browser pages, but just make sure to not X out of, or close, the testing page. You can minimize it, though, if you wish.
For upload only testing, it should be set up like this...
Note that only Upload is ticked (not Combined), and 3MB is chosen for the upload size, with nothing chosen for the download size. Also note the "nfw" box is checked. And, again, I chose every 5 minutes for 5 times, so that it only runs a total of five tests each time you have it set up like this and click on "Start Automatic Test".
Now, the browser page MUST remain open in order for the tests to run. If the testmy.net browser page is closed, the tests won't run. But, why it continued to run for you after it completed the set number of tests I don't know. With it set to run five times it should ONLY run five times, then stop.
I'm going to run a set of upload tests and see what happens. I'll use what's set in the picture above for the upload only testing, though I'll use the 4MB size due to having Gen5. I'll leave it open for more than an hour to see if the testing starts again in the next hour. It shouldn't, as in after I click "Start Automatic Test" it should only run the five tests that it's set to run and no more, but nothing is infallible. I'll post what happens.
P.S. Note that the "Extra Identifier" in the testing setup is something you would set if you run tests using multiple devices on the same account and you use a specific identifier for each device, so you know which is which when looking at the results. If you click and look through the options you will see what I mean by Identifier. So, if you do have Identifiers set up you should probably choose the one that you use for the device with which you are testing. If you don't use identifiers, just leave the Extra Identifier thing alone. It's not something that's required to use. It can just make it easier for you if you use a lot of devices and you want to know which results belong to which device tested. As an example, I use the "Laptop" identifier for my laptop. This way, when I look through my results, I can see which test results belong to my laptop. I use Location 5 for my desktop, just to signify Gen5, though I should use Home or Living Room or something. There's no "Desktop" identifier available, which is kind of stupid if you ask me. :p
GabeU,
Ok, finally got Testmy.net figured out except for one issue, combined testing with max data set.
You see the tabs to the right of 'optional'? Both will set the 'minimum' data size but won't affect the maximum so it still tests anything it wants and of course, if it tests something reasonable the first time and runs quickly it will rerun with more data the next time so it is very important that I remember to click nfw. I'm following your instructions but unless I test upload and download separately I have no control over the maximum data used.
Hughes Level 4 called today (1/11/19) and when she had me run the upload test it was 33Kbps up and 21.3 down. Unplug the modem, bypass the router, long periods of silence and 'still buffering' for 25 minutes until it finally steamed without buffering but I haven't a clue what she did and I got the idea that she had a quota on either words or characters used, kink of like Twitter. I appreciated what ever she did but as she trying to get off the phone I asked if 2215 ms ping rate wasn't a touch long. She said she didn't know, 'bye'. I've never asked any tech about that before so I don't know if only certain techs are familiar with ping rates. I let it go and won't complain unless it becomes a consistant issue. What is your average ping rate? I don't know if testmy.net arbitrarily picks Dallas to ping but that's what this is testing. I understand that a high ping rate will affect the loading of a page which is what I'm running into. Slow to connect, handshake, etc. but once loaded it streams with litte buffering now. She must have done something, 1.5 Mbps up - 25Mbps down. Just so it stays. Thanks for the info.
Oh, you're right, I wasn't able to see that your note about being out of data was addressed to someone else. I've yet to figure out this board.
